Open late: Mon–Fri 9 AM–7 PM · Sat 9 AM–6 PMNew & used equipment · Free local delivery $500+ · Repair · We buy used(945) 394-0396

Commercial Fryer Buying Guide: Gas vs. Electric, Sizes and Oil Capacity

Open-pot vs. tube vs. flat-bottom, gas vs. electric, oil capacity, filtration and efficiency.

By Q Restaurant Supply, Irving, TX · Updated November 13, 2026. General guidance only. Always confirm details for your own kitchen and local code requirements.

Fries, wings, chicken, fish, egg rolls, funnel cakes: for a lot of menus, the fryer does more work than almost anything else on the line. Choosing the right one affects food quality, speed of service, oil costs and energy bills. This guide covers the main fryer types, gas vs. electric, sizing by oil capacity, filtration and efficiency, drawing on Foodservice Equipment & Supplies, ENERGY STAR and manufacturer Pitco.

Q Restaurant Supply sells new and used commercial fryers. See our fryers page or call (945) 394-0396.

Start with your menu

FE&S stresses that the menu comes first, because some fryer designs are built for particular foods. It also points out that cooking different foods in the same oil can cause flavor transfer. If you fry fish and fries, or you cook to order, several smaller fryers can work better than one large one.

Types of fryers

Open-pot (open-vat) fryers

The heat source is on the outside of the tank, leaving the inside open and easy to clean. A narrow cold zone at the bottom collects crumbs and sediment. FE&S calls open-vat fryers the best fit for menus that are mostly unbreaded or lightly breaded, like fries and wings.

Tube-type fryers

Gas tubes run through the oil near the bottom of the pot, above a wide cold zone that traps more sediment. FE&S says this makes tube fryers ideal for heavily breaded and battered food like onion rings and battered chicken, and good for delicate items like fish. The trade-off is that the tubes make the pot harder to clean.

Flat-bottom fryers

These have a shallow, flat pot with no cold zone. FE&S recommends them for items like taco shells and tempura, not for high-volume frying.

Pressure fryers

These cook under pressure to raise the oil’s boiling point. FE&S says this cooks food quickly with a juicy result and less grease, which is popular for bone-in chicken.

Countertop and ventless fryers

Countertop fryers suit smaller volumes and tight spaces. FE&S notes that ventless countertop fryers, often with 2- to 3-lb oil capacities, are best for low-volume use and are designed so you don’t need a hood. Always confirm with your local code official before running any fryer without a hood.

Gas vs. electric fryers

FE&S notes that the utility type affects recovery rate, meaning how quickly the oil gets back to temperature after you drop cold or frozen food, and how you batch product.

Gas fryersElectric fryers
Heat-up and recoveryHigh-BTU models heat quickly for high volumeHeat quickly, with fast recovery
Temperature controlPrecise control availableGood control and temperature retention
UtilitiesNeed a gas line (natural or LP)Need the right voltage and phase; no gas line
MobilityFixed to the gas connectionEasier to move
ENERGY STARCertified standard and large-vat models are about 30% more efficient than standard modelsCertified standard-vat models are about 17% more efficient than standard models

What’s already in your building often decides it. If you have gas on the line and a hood, gas is common. If you don’t have gas available, or need flexibility, electric may fit better. Pitco’s Solstice Supreme gas line offers higher-BTU "R" models with taller burner tubes for operators who need more power from the same fryer size.

Important: Q doesn’t install fryers or do gas hookups. Use a licensed gas plumber for gas connections and a licensed electrician for electric fryers.

Sizing: oil capacity and production

Fryers are commonly described by how many pounds of oil the tank holds. FE&S reports tank sizes ranging from about 20 to 80 lb.

A quick production estimate

FE&S offers a rule of thumb: multiply the pounds of oil by 1.5 to 2 for a rough estimate of pounds of food per hour. For example, a 50-lb fryer would handle roughly 75 to 100 lb of product per hour. The real number depends on whether the food is refrigerated or frozen, and on how big and thick each piece is.

Common sizes

  • Fry pot width: ENERGY STAR defines "standard" fryers as having vats at least 12 inches and under 18 inches wide, and "large vat" fryers as 18 to 24 inches wide.
  • Pitco example: Pitco’s Solstice Supreme SSH55 has a 14 x 14-inch frying area. The SSH60 is described as stepping up from 40–50 lb to 50–60 lb of oil, and the SSH75 holds 75 lb.
  • Split-vat fryers divide the tank in two, so you can fry two different foods, or run only half the fryer during slow hours. Pitco offers split-tank models in its Solstice Supreme line.

Look at each shift’s volume when sizing. FE&S notes manufacturers often rate fryers by pounds of product per hour.

Filtration: protect your oil

FE&S calls clean oil the biggest issue with fryers. Good filtration improves food quality and extends the fryer’s service life. Its guidance:

  • Filter daily and skim the oil throughout the day.
  • Built-in filter drawers add safety and make filtering simpler.
  • Automatic filtration helps high-volume kitchens filter more safely and keep product consistent.
  • Central oil filtration and recovery serves several fryers at once in large operations.
  • Automatic top-off keeps the oil at the right level. Pitco offers automatic filtration and oil top-off on its Solstice Supreme fryers.

Change the oil if food comes out dark, greasy or bad-tasting, if the oil is dark brown or black, if it smokes or foams heavily, or if it smells off (FE&S).

Controls and labor savers

  • Thermostat controls: simple dial (solid state) or digital
  • Programmable computers set cook times by menu item for consistency
  • Automatic basket lifts raise baskets when the timer ends
  • Basket shakers help keep product from sticking together

Energy efficiency

ENERGY STAR-certified fryers have to meet minimum cooking-energy efficiency and maximum idle energy rates. Under the current ENERGY STAR spec, standard gas fryers must exceed 50% heavy-load cooking efficiency, and standard electric fryers must exceed 83%. Because fryers often run all day, idle energy adds up. Ask whether a model is ENERGY STAR certified.

Ventilation and safety

Commercial fryers generally need to go under a ventilation hood to handle grease and smoke (FE&S). Q sells and installs new kitchen hoods. Our installation covers the hood only, not ductwork, makeup air, fire suppression or permits. See ventilation hoods.

FE&S also notes that testing the high-limit thermostat should be done only by an authorized service agent.

Buying a used fryer

Used fryers can be a good value, but inspect them closely. FE&S says the clearest sign a fryer needs replacing is a leaking tank, often shown by hardened oil under the fryer and behind the door. Check that it heats up and holds temperature, and look for dents, rust and missing parts. See our new vs. used equipment guide.

Shop fryers at Q

Compare new and used fryers and other cooking equipment at our Irving showroom, or call (945) 394-0396.

Frequently asked questions

Is a gas or electric fryer better?

Neither wins every time. Gas is common in high-volume kitchens that already have gas and a hood. Electric heats quickly and is easier to move. Your utilities often decide it.

What size fryer do I need?

A rough rule from FE&S: pounds of oil × 1.5 to 2 = pounds of food per hour. Then check menu, peak volume and whether food goes in frozen.

Tube fryer or open-pot fryer?

Tube fryers handle heavily breaded food well thanks to the big cold zone. Open-pot fryers are easier to clean and suit fries and lightly breaded items.

Does Q hook up gas fryers?

No. Q doesn’t install fryers or do gas hookups. Use a licensed gas professional.

Do I need a hood for a fryer?

Most commercial fryers need one. Check with your local code official.

Call NowDirections